Functional requirements analysis and design of wearable multi-channel sensing system

Xingyu Ma, Hengzhen Shi, Yuehui Hu, Yini Ren, Wuwei Kang, Tao Jin, Yang Wang, Piao Dai

Article ID: 1635
Vol 2, Issue 2, 2021
DOI: https://doi.org/10.54517/wt.v2i2.1635
VIEWS - 1641 (Abstract)

Download PDF

Abstract

In recent years, a large number of wearable devices have emerged; and users have higher and higher functional requirements for wearable devices. However, the realization of complex functions of wearable devices often depends on the real-time acquisition of multi-channel sensing signals. Taking the wearable 8-channel PVDF sensor system as an example; this paper studies the functional requirements of this kind of system. It is found that the flexible ultra-thin and long endurance time are two obvious characteristics of this kind of equipment. The key technical problems of the system are completed, such as the selection of MCU, the coding design of multi-channel sensing data, the transmission mode design of multi-channel sensing data and the low power consumption design of the system. A practical design scheme of reliable wearable multi-channel sensor system is designed. This scheme also provides a reliable reference for the design and development of wearable multi-channel sensor system.


Keywords

wearable equipment; system design; demand analysis; multi-channel; PVDF sensor; coding method; mode of transmission


References

1. Shui Z. Printing electronic technology sets off a revolution in intelligent wearable applications. Integrated Circuit Application 2015; (11): 16–18.

2. Zhu J. Preparation and properties of PVDF piezoelectric film and its sensor [Master’s thesis]. Harbin: Harbin Institute of Technology; 2011.

3. Xiao Y. Functional requirements analysis of automatic driving signal system. Railway Communication Signal 2014; 50(12): 39–42.

4. Yu W, Xie Z. Design of ECG monitoring system based on wearable. Sensors and Microsystems 2015; 34(9): 65–68.

5. Qian C. Design and application of a multi-purpose low-power detection system [Master’s thesis]. Qingdao: Shandong University of Science and Technology; 2003.

6. Liu M. Analysis of MCU selection in portable medical electronic instrument design. Comprehensive Review of Chinese Journal of Medical Devices 2014; 38(3): 202–206.

7. Reference Manual of STM32F 10XXX Series Products Based on Arm32-Bit Kernel, 10th ed. STMicroelectronics; 2010 January; Grenoble, France.

8. STM32F 103xx Datasheet, 10th ed. STMicroelectronics; 2009 April; Grenoble, France.

9. STM32L 100XX; STM32L 151xx; STM32L 152xx and STM32L 162xx Series Reference Manual. STMicroelectronics; Grenoble, France.

10. RL78/G13Datasheet, 3.30 ed. Renesas Electronics Corporation; 2016 March; Tokyo, Japan.

11. PIC24FJ256GB110 Series Data Manual. Microchip Technology Inc.; 2009; Chandler, USA.

12. MSP430F522x/MSP430F521x Mixed Signal Microcontroller Data Manual, 5th ed. Electronics Corporation, Tokyo, Japan.

13. Chen S. Analysis and Simulation of ADPCM speech compression coding. Western China Science and Technology 2008; 7(32): 52–54.

14. Liu X. Rapid software implementation of CRC verification in single chip microcomputer system. Journal of Fujian Institute of Engineering 2007; 5(1): 76–78.

15. Zhang S. Implemented with MSP430_ 2_ 1_ 4_ Convolutional code coding and Viterbi decoding. Journal of Beijing Broadcasting Institute 2005; 12(1): 24–30.

16. Xu W. Joint source and channel coding [Master’s thesis]. Hefei: University of Science and Technology of China; 2002

17. Wu M. Design and implementation of underlying software of several sensors based on I2C bus protocol in Android system [Master’s thesis]. Xi’an: Xidian University; 2012.

18. Meng X. Research on data acquisition system based on USB interface [Master’s thesis]. Qingdao: Shandong University of Science and Technology; 2004.

19. Yang M, Li X. SPI interface and its application in data exchange. Communication Technology 2007; 40(11): 385–387.

20. Wu W, Hu B, Zhang M. Two implementations of I2C bus driver in embedded system. Modern Electronic Technology 2007; (8): 56–58.

21. Xu Y, Hu C, Yao G. Design and implementation of infrared transmission function based on object exchange protocol in handheld terminal equipment. Electronic Devices 2007; 30(1): 215–218.

22. Zhang F, Zhang C. Research on short-range wireless communication technology and its fusion development. Electrical Measurement and Instrumentation 2007; 44(10): 48–52.

23. NFC Industrial Network Discuss the prospect and future of NFC wearable devices from the perspective of application. Golden Card Project 2013; (11): 40–41.

24. Guo Y. Preparing for wearable devices Bluetooth 4.1 analysis. Computer Fan 2014; (6): 64.

25. Zhou Y. Application research on lithium battery management system of electric vehicle based on smart phone [Master’s thesis]. Changchun: Jilin University; 2014.

26. TLV707xx, TLV707xxP Datasheet. Texas Instruments; 2015; Dallas, Texas.

27. MAX9617-MAX9620 Datasheet, 7th ed. Maxim Integrated, San Jose, CA, USA; pp.19–4753.

28. Zhang X. Design of power data acquisition system based on STM32. Electronic Measurement Technology 2010; 33(11): 90–93.

29. Lu Z. Research on key technologies of wearable health monitoring and interpersonal interaction [PhD Thesis]. Hefei: University of Science and Technology of China; 2014.

Refbacks

  • There are currently no refbacks.


Copyright (c) 2021 Xingyu Ma, Hengzhen Shi, Yuehui Hu, Yini Ren, Wuwei Kang, Tao Jin, Yang Wang, Piao Dai

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.